The Wiremold 2000 Series Raceway Offers A Selection Of Steel, Aluminum, and Nonmetallic Raceways That Provide A Versatile Solution For Many Applications. Plugmold Sections Offer Single or Alternating Circuits, In Standard or Isolated Ground Receptacles. The Scuffcoat Finish Is Scratch Resistant and Protects Against Nicks and Chips While Preventing Color From Fading.

Floorport Service Fittings For Resource RFB® Series Floor Boxes, Walkercell® Cellular Raceway, and Walkerdeck Systems Provide Flexibility In Recessed and Furniture Feed Applications. The Enhanced Design Also Increases The Ease Of Use and Color Options While Continuing to Exceed Ul Scrub Water Requirements. These Covers Are Ideal For Use In A Wide Variety Of Applications Including Educational Facilities, Airports, and Commercial and Institutional Office Buildings. The Covers Are Ul Listed to U.S. and Canadi

<P>Accepts Two (2) Wiremold CM Series Open System Adapters (Sold Separately). Note: For Use With RFB4E, RFB6, RFB6E Series Floor Boxes.</P>

For Use In Concrete Floors. For Use With Round Evolution Series Cover. Fully Adjustable With Tunnel Compartments. Supplied With Two (2) Duplex Mounting Plates. Other Plates Sold Separately.

Tee, Steel, Ivory, Scuffcoat, 7/8 In Width, 2-1/2 In Height, 0.17 LB/Ea

For Deep Devices Such As Momentary Contact, Remote Control Switches, and Hospital Signaling System Devices. Base Has 1/2" Trade Size Kos. Larger Gang Boxes Available By Special Order. Two-Gang: 4 3/4" L X 4 3/4" W (121MM X 121MM). Accepts Nema Double-Gang Standard Faceplates. Note: Certified to Canadian Safety Standards For Sale In Canada. When Ordering These Products, Change The "V" Color Prefix to "VC" or The "WH" Color Suffix to "WHC" to Denote The Canadian Versions. Ivory

Wiremold 500 Series and 700 Series Raceways Are Ideal For Surface Mounting Small Amounts Of Electrical Wiring or Communication Cables. These Rugged Raceways Offer A Low Profile Appearance Which Blend With Any Decor. Available In Our Exclusive Scuffcoat Finish.

For Holding The Conductors In Place. Not Ul Listed.

<P>For Right Angle Turns On The Same Surface.</P>

<P>May Be Used As A Cross, Tee or Elbow. Cover Has 1/2'' Trade Size Ko. Base Has 1/2'' and 3/4'' Concentric Trade Size Kos to Enable Connection to Floor Outlet Boxes or Underfloor Duct Systems (Use Chase Nipple Not Included). Two 1500WC Wire Clips Included.</P>

<P>Will Accommodate Commercially Available 15A or 20A Duplex Receptacles. Base Has 1/2'' and 3/4'' Concentric Trade Size Kos. Nonmetallic Cover Has 1500 and 2600 Series Raceway Twistouts On All Four Sides. Two 1500WC Wire Clips Included. Side Wiring Recommended. Gray Finish. Note: Certified to Canadian Safety Standards. For Sale In Canada. When Ordering These Products, Add ''C'' Prefix to Part Number to Denote The Canadian Version, I.E ''C1546B''.</P>

<P>Connects Equipment Grounding Conductor. Provides An Additional Ground For Raceway.</P>

<P>For Covering Joint Where Two Pieces Of 2300BAC Series Raceway Cover Come Together.</P>

<P>Divided Fitting to Feed 2300 and 2300 Divided Series Raceway. Includes 1/2'', 3/4'', and 1'' Trade Size Kos On Back and Top.</P>

2300 Series Flat Elbow. For Right Angle Turns On Same Surface. Finish - Ivory

Use With Any Nonmetallic Round Device Box to Convert Into A Junction Box. White

One-Gang. Base Has Rectangular Ko. Accepts Industry Standard Faceplates For Switch and Communication Devices. Note: All Boxes Have Combination Twistouts For 400BAC, 800BAC, and 2300BAC On All Four Sides. Ivory

For Use With 2300D Series Divided Raceway When Additional Depth Is Required. For Mounting Standard Switches, Receptacles, and Industry Standard Faceplates For Communication Devices. Ivory

<P>Divided Two-Gang Box For Use With 2300D Series Divided Raceway. Provides The Ability to Have Both Power and Low Voltage At A Single Point Of Use. Utilizes 5507 Series Faceplates, As Well As Wiremold Open System Communication Modules, Ortronics Tracjack and Series Ii Inserts, and Pass and Seymour Activate Series Inserts. Note: CM-Epla End Plates Are Required When Using Wiremold CM2 Communication Modules and Pass and Seymour Activate Series Inserts. S2-Epl End Plates Are Required When Using Ortronics Seri

Joins The Lengths Of 2400B Base Together.